LOADSENSOR KIT CRAM

LOADSENSOR KIT VERSIONS

The over-load controls by Cram can to measure the load in the cabin by observing of the deformation of the arch, the cable tension, the direct measurement.
They do not require any structural changes for installation and have extreme sensitivity and resistance, being able to measure both the lowest and the highest loads. The over-load controls produced by Cram feature simplicity of installation of all models and direct and intuitive calibration.

technical sheet

Electronic remote-controlled 7CRX. Alternative to traditional digital electronics 2CAX, compatible with all sensors SBOT, CLR1, CLR2, PTG1, PTG2

Electronic with internal display 7CAD. Alternative to traditional digital electronics 2CAX, compatible with all sensors SBOT, CLR1, CLR2, PTG1, PTG2

Loadsensor kit with deformation sensor CRL1
Easy intallation and calibration.. Sensor made with iron high-resistance, little size (90x25x20h mm). Directly application at beam or mechanical structure. Without modify at structure existent. High sensibility. Good accuracy. Standard cable 700 mm, 5 wires. Protection at umidity, temperature, dust. Supplied with screw-kit.
Applications

Electronic part 7CRX , with radiocontrol , combine to sensor …

Electronic part with all digital command, with internal receiver , calibration with radiocontrol RR.
Activation of calibration , make with a wiring remote .
Once attached and wired, the other does not require electronic transactions (for bothcalibration for operation).
Supplied with 1...4 programmable set-point (the X is the number of set-point).
The electronic part is supplied with box and pratical cover (without screw).
The memorization of zero and set-point, is make with radiocontrol RR , to remote position.
The electronic have a little horn, with that is possible control the correct procedure.
The power applicable are continuos mode or alternate mode.
Possibility of percentage calibration, with small load make a calibration of big set-point.
Electronic part with digital port serial-out (other application).
Electronic part with analog out 0…10Vcc, for feedback of inverter.

Radio control RR Tool UNA-TANTUM
Essential for the operation of electronics 7CRX (but common for the operation of all electronic 7CRX)

Display VISO-2C (OPTIONAL)
Supplied in resistant aluminium-box. Connectable by the serial port of the all digital-out. LCD Display, with reflective-led. Possibility of Display of the current-load. Possibility of Display of the memorization.

Total plate for ropes PTG1.
Iron plate 100 x 120 mm. For system with max 8 ropes (max 2500 kg). Version PTG1-5 for ropes 5 ... 6mm. Version PTG1-6 for ropes 6,5 ... 8mm. Version PTG1-std for ropes 9 ... 11mm. Version PTG1-13 for ropes 12 ... 13mm. Easy calibration and installation. Applied only for n° 3 screws.. Without structurally intervent for applied. Semi-direct measure, good accuracy.. High sensibility. Standard cable 2 meter. Protection at humidity, temperature and dust..	<
Applications

Electronic part 7CRX , with radiocontrol , combine to sensor …

Electronic part with all digital command, with internal receiver , calibration with radiocontrol RR.
Activation of calibration , make with a wiring remote .
Once attached and wired, the other does not require electronic transactions (for bothcalibration for operation).
Supplied with 1...4 programmable set-point (the X is the number of set-point).
The electronic part is supplied with box and pratical cover (without screw).
The memorization of zero and set-point, is make with radiocontrol RR , to remote position.
The electronic have a little horn, with that is possible control the correct procedure.
The power applicable are continuos mode or alternate mode.
Possibility of percentage calibration, with small load make a calibration of big set-point.
Electronic part with digital port serial-out (other application).
Electronic part with analog out 0…10Vcc, for feedback of inverter.

Radio control RR tool UNA-TANTUM
Essential for the operation of electronics 7CRX (but common for the operation of all electronic 7CRX).

Display VISO-2C (OPTIONAL)
Supplied in resistant aluminium-box. Connectable by the serial port of the all digital-out. LCD Display, with reflective-led. Possibility of Display of the current-load. Possibility of Display of the memorization.

Compression sensor SBOT

VERY CHEAP

Loadsensor kit with deformation sensor CRL1

VERY CHEAP

Deformation sensor CRL1, indirect measure.
Easy intallation and calibration.. Sensor made with iron high-resistance, little size (90x25x20h mm). Directly application at beam or mechanical structure. Without modify at structure existent. High sensibility. Good accuracy.. Standard cable 700 mm, 5 wires. Protection at umidity, temperature, dust. Supplied with screw-kit.
Applications

Electronic part 2C-Ax, to install with CR-L1 (indirect measure).

Electronic part with all digital command, no trimmer or analogic regulation.
Supplied with 1...4 programmable set-point (the X is the number of set-point).
The electronic part is supplied with box and pratical cover (without screw).
Little size 120x110x30h mm, with fixed point.
The memorization of zero and set-point, is make with only push-button.
The electronic have the led indicator, with that is possible control the correct procedure.
The power applicable are continuos mode or alternate mode.
Possibility of percentual calibration, with small load make a calibration of big set-point.
Possibility of modify set-point, without load.
Electronic part with digital port serial-out (other application).
Supplied with a little connector or board for the analogic output.
Electronic part with analog out 0…10Vcc, for feedback of inverter.
Supplied with a connector for the remote control part.
Programmable on board or with remote tool.

Display VISO-2C (OPTIONAL)
Supplied in resistant aluminium-box. Connectable by the serial port of the all digital-out. LCD Display, with reflective-led. Possibility of Display of the current-load. Possibility of Display of the memorization.

Loadsensor kit with deformation sensor CRL2 small lenght 70mm

VERY CHEAP

Deformation sensor CRL2 small length 70mm, indirect measure.
Easy intallation and calibration.. Sensor made with iron high-resistance, little size (70x25x20h mm). Directly application at beam or mechanical structure. Without modify at structure existent. High sensibility. Good accuracy.. Standard cable 700 mm, 5 wires. Protection at umidity, temperature, dust. Supplied with screw-kit.
Applications

Electronic part 2C-Ax, to install with CR-L2 (indirect measure).

Electronic part with all digital command, no trimmer or analogic regulation.
Supplied with 1...4 programmable set-point (the X is the number of set-point).
The electronic part is supplied with box and pratical cover (without screw).
Little size 120x110x30h mm, with fixed point.
The memorization of zero and set-point, is make with only push-button.
The electronic have the led indicator, with that is possible control the correct procedure.
The power applicable are continuos mode or alternate mode.
Possibility of percentual calibration, with small load make a calibration of big set-point.
Possibility of modify set-point, without load.
Electronic part with digital port serial-out (other application).
Supplied with a little connector or board for the analogic output.
Electronic part with analog out 0…10Vcc, for feedback of inverter.
Supplied with a connector for the remote control part.
Programmable on board or with remote tool.

Display VISO-2C (OPTIONAL)
Supplied in resistant aluminium-box. Connectable by the serial port of the all digital-out. LCD Display, with reflective-led. Possibility of Display of the current-load. Possibility of Display of the memorization.

Loadsensor kit with total plate for ropes PTG1

VERY CHEAP

Total plate for ropes PTG1.
Iron plate 100 x 120 mm. Version PTG1-5 for ropes 5 ... 6mm. Version PTG1-6 for ropes 6,5 ... 8mm. Version PTG1-std for ropes 9 ... 11mm. Version PTG1-13 for ropes 12 ... 13mm. Easy calibration and installation. Applied only for n° 3 screws.. Without structurally intervent for applied. Semi-direct measure, good accuracy.. High sensibility. Standard cable 2 meter. Protection at humidity, temperature and dust..
Applications

Electronic part 2C-Ax, to install with PTG1 (indirect measure).

Electronic part with all digital command, no trimmer or analogic regulation.
Supplied with 1...4 programmable set-point (the X is the number of set-point).
The electronic part is supplied with box and pratical cover (without screw).
LIttle size 120x110x30h mm, with fixed point.
The memorization of zero and set-point, is make with only push-button.
The electronic have the led indicator, with that is possible control the correct procedure.
The power applicable are continuos mode or alternate mode.
Possibility of percentual calibration, with small load make a calibration of big set-point.
Possibility of modify set-point, without load.
Electronic part with digital port serial-out (other application).
Suppy with a little connector or board for the analogic output.
Electronic part with analog out 0…10Vcc, for feedback of inverter.
Supplied with a connector for the remote control part.
Programmable on board or with remote tool.

Display VISO-2C (OPTIONAL)
Supplied in resistant aluminium-box. Connectable by the serial port of the all digital-out. LCD Display, with reflective-led. Possibility of Display of the current-load. Possibility of Display of the memorization.

Loadsensor kit with total plate for ropes PTG2 - "slim" version -

VERY CHEAP

Total plate for ropes PTG2 - "slim version" - .

Iron plate 100 x 120 mm.
Version PTG2-5 for ropes from 5 to 6,5mm nr. 5/6 ropes.
Version PTG2-std for ropes from 8 to 11mm nr. 4/5 ropes.
Version PTG2-13 for ropes from 12 to 13mm nr. 3 ropes.
Easy calibration and installation.
Applied only for n° 2 screws..
Without structurally intervent for applied.
Semi-direct measure, good accuracy.
High sensibility.
Standard cable 2 meter.
Protection at humidity, temperature and dust.

Electronic part 2C-Ax, to install with CR-L1 (indirect measure).

Electronic part with all digital command, no trimmer or analogic regulation.
Supplied with 1...4 programmable set-point (the X is the number of set-point).
The electronic part is supplied with box and pratical cover (without screw).
LIttle size 120x110x30h mm, with fixed point.
The memorization of zero and set-point, is make with only push-button.
The electronic have the led indicator, with that is possible control the correct procedure.
The power applicable are continuos mode or alternate mode.
Possibility of percentual calibration, with small load make a calibration of big set-point.
Possibility of modify set-point, without load.
Electronic part with digital port serial-out (other application).
Suppy with a little connector or board for the analogic output.
Electronic part with analog out 0…10Vcc, for feedback of inverter.
Supplied with a connector for the remote control part.
Programmable on board or with remote tool.

Display VISO-2C (OPTIONAL)
Supplied in resistant aluminium-box. Connectable by the serial port of the all digital-out. LCD Display, with reflective-led. Possibility of Display of the current-load. Possibility of Display of the memorization.

FN loadsensor kit electronic FN and with independent sensors for ropes

Calibration without load

Sensor for ropes type SN - A
Calibration without load. One sensor for one rope. Easy installation (two screws). Don't have to force, fit, perforate or disassemble anything. Pre-configured product. Version SNA-6 for ropes 5, 6, 6,5mm. Version SNA-std for ropes 7, 8, 9, 10, 11mm. Version SNA-13 for ropes 12, 13mm Very good accuration of measure. Standard cable of 2 meters. Protection against temperature, humidity, dust. Very hard structure.
Applications

Electronic type FN - A

Calibration without load.
Totally digital dispositive; without trimmer or regulation.
3 set point.
The electronic part is supplied with box and pratical cover (without screws).
Small dimension 120x110x30h mm.
Stop load function.
Fully calibratelly trought serial-line with programming box FN.
The applicable power are:
- continuos mode
- alternate mode
No load for selection of set point (need only rope diameters).
Set point directly programming in kilograms.
Possibility of modify set-point without load.

Programming box for kit FN - A (UNA TANTUM)
Display type semi-graphic. Immediated and guided indication for calibration. Very small dimension. The programming box use a serial connector only in the stage of calibration; that is unstuck from the local plant and you will never have to use it for the functioning of the load sensor .

Sensor under cabin SC with electronic part FN.

Calibration without load

PARAMETER	VALUE	UNIT
POWER RANGE VCC	16...50	V
POWER RANGE VAC	12...36	V
TYPICAL POWER CONSUMPTION	0,15	V
LINEARITY	±0,01	% del FS
TEMPERATURE RANGE	0...50	°C
STABILITY OF ZERO POINT – TEMPERATURE RANGE	±0,5	% del FS
STABILITY OF GAIN – TEMPERATURE RANGE	±0,5	% del FS
UMIDITY MAX	93	% (not condensing)

Specialists in load control for elevator

LOADSENSOR KIT VERSIONS

Electronic remote-controlled 7CRX. Alternative to traditional digital electronics 2CAX, compatible with all sensors SBOT, CLR1, CLR2, PTG1, PTG2

Electronic with internal display 7CAD. Alternative to traditional digital electronics 2CAX, compatible with all sensors SBOT, CLR1, CLR2, PTG1, PTG2

Compression sensor SBOT

Loadsensor kit with deformation sensor CRL1

Loadsensor kit with deformation sensor CRL2 small lenght 70mm

Loadsensor kit with total plate for ropes PTG1

Loadsensor kit with total plate for ropes PTG2 - "slim" version -

FN loadsensor kit electronic FN and with independent sensors for ropes

Sensor under cabin SC with electronic part FN.

KIT SBOT / 2CAX

Technical specification , complete kit with sensor and electronic part.

OPTIONAL - DISPLAY TYPE VISO-2C - UNA-TANTUM TOOL